A YouTuber Made a Water-Cooling Rig to Combat the Canon R5’s Overheating Issues

TheCanon R5is a badly impressive camera and one of the cheapest mirrorless camera you’re able to grease one’s palms that bear full 8 K video seizure . unluckily , those fancy video capabilities come with a serious drawback : major overheating issues . So to address the R5 ’s limitation , YouTuber Matt Perks make a custom cool solution to seriously kick upstairs the Canon R5 ’s max transcription time .

When it first went on sales agreement , the R5 ( which sells for just under $ 4,000 body only ) total with a surd 20 - minute transcription point of accumulation imposed by Canon for 8 kB television capture . And with a design that often sees components wall its processor reach temperature of 82 degree Celsius or more during normal use , after you reach the camera ’s 20 - minute recording limit , it can take up to two hour for the camera to cool off down before being usable again .

After take his Canon R5 aside , Matt Perks of the DIY Perks YouTube channeldiscovered one of the grownup reason for the R5 ’s overheating issues is triggered by a heatsink that ’s attached to a central processing unit by two caloric launch area that do n’t even fully wrap up the chip , result in rather pathetic caloric conductivity and temperature reduction . So to set up this , Perks created his own customs water - cooling semi for the R5 made from a copper color heatsink installed with a clean layer of thermal spread , that was then connected to a pair of lowly piddle engine block bond to expectant extraneous radiator and reservoir .

Screenshot:Matt Perks/YouTube(Other)

Unfortunately , due to Canon ’s severe 20 - min video recording limitation , even after perquisite ’ raw piddle - cooling organization was installed , the R5 still shut down mechanically around the 20 - minute print even though data from a thermal camera show temps of less than 40 degrees Celsius . gratefully , be substance abuser complaints , Canon released raw firmware for the R5 ( version 1.1.1 ) that got rid of the arbitrary 20 - minute transcription cap in favour of a new temperature - establish overheating detecting . And voila , after Perks updated his R5 with the new firmware , he find that with his water - cool down organization , his Canon R5 was capable to record 8 K video for more than fours without stopping .

https://gizmodo.com/the-eos-r5-looks-like-the-beastly-full-frame-mirrorless-1844321536

However , as telling as his results were using the water - cooling system of rules , it ’s not exactly a pragmatic solution , as the tubes and water block Perks used made treatment and lock the camera quite hard . So as a center ground answer between maximum cooling system and usability , Perks created a 2nd custom copper heatsink that stretch forth the R5 ’s bloodline 4 KiB video recording time from 26 minutes to 39 second of uninterrupted use . But perhaps the biggest melioration is that with his new bull heatsink , Perks says the R5 only demand to hold off around five minutes after overheat to be able-bodied to record TV again , a massive improvement from the two hour wait meter of a stock certificate Canon R5 .

While it’s a bit rough, Perks’ fan add-on could be easily mistaken for an extended battery grip, while the rest of the R5 appears completely stock.

While it’s a bit rough, Perks’ fan add-on could be easily mistaken for an extended battery grip, while the rest of the R5 appears completely stock.Screenshot:Matt Perks/YouTube(Other)

But lease ’s not block that Perks original destination was unlimited recording clip . So after installing his customer Cu heatsink , Perks designed a novel battery - power fan accessory that can be attached to the bottom of the camera to botch up air and draw heat away from the camera ’s body and interior heatsink , which ply enough cooling to permit the R5 to record video indefinitely . And thanks to the sports fan ’s custom 3D - impress saddle horse , Perks ’ attention deficit hyperactivity disorder - on can be connected and removed quickly and easily depending on your motive .

While all the steps needed to combat the R5 ’s overheating progeny might be a bit too complicated for your distinctive photographic camera drug user , Perk ’s DIY solution is still an telling example of what can be accomplished by ( expertly ) tinker with your widget . And here ’s hoping he will release a file for his 3-D printed base so some other enterprising R5 owner can promote their cameras too .

CamerasConsumer TechMirrorless CamerasYouTube

How To Watch French Open Live On A Free Channel